Compatibilité Homelink LS 430

Coco24 · 06-04-2019 18:24:00

Bonjour à tous,

Ayant aperçu qu'outre atlantique, les Lexus LS 430 (et d'autres modèles) pouvaient être fournies avec le système d'ouverture de portes de garage/portail Homelink, je me demandais s'il était possible d'adapter un système d'origine sur une LS 430 non équipée d'origine ? Le système étant embarqué dans la console au niveau du plafonnier avant, il faudra nécessairement remplacer la totalité de la pièce.

Des personnes qui ont déjà tenté la modif ?

Marcusvdw · 06-04-2019 21:08:27

Pour moi, le systéme est complètement intégré dans le rétroviseur pour les IS..

C'est alimenté directement par là ... n'est-ce pas aussi le cas pour les LS ?

Coco24 · 08-04-2019 19:49:36

Pour les LS de ces années là, le système est intégré dans le cerclage en plastique du plafonnier central, à côté du micro.
Je me demandais surtout si le système américain pouvais fonctionner avec nos portails et portes de garage français.
Par principe je dirais que ce sont les mêmes fréquences avec les mêmes protocoles de communication, mais sait on jamais smile

Astrix64 · 08-04-2019 20:07:26

Chaque pays à ces propres fréquences.

Mais rassure toi, la doc indique que l'on peut choisir son pays et le type d'encodage en fonction de la marque du portail pour l'apprentissage.

Tony Moz · 16-05-2019 13:01:09

Slt, comment paramétrer ce " cercle" si l'on n'a pas le livret d'utilisation ? ( LS 430 )
merci

Astrix64 · 16-05-2019 20:57:20

Voici ce que j'ai trouvé sur une LS430 de 2004:

GARAGE DOOR OPENERThe garage door opener (UniversalTransceiver) is manufactured under license fromHomeLink and can be programmed to operate garagedoors, gates, entry doors, door locks, home lightingsystems, and security systems, etc.

(a) Programming the HomeLink. The HomeLink in your vehicle has 3 buttons and you canstore one program for each button.To ensure correct programming into the HomeLink, install anew battery in the hand-held transmitter prior to programming.

The battery side of the hand-held transmitter must be pointedaway from the HomeLink during the programming process.For Canadian users, follow the procedure in “Programming anentrance gate/Programming all devices in the Canadianmarket”.
1. Decide which of 3 HomeLink buttons you want to program.
2. Place your hand-held garage transmitter 25 to 75 mm (1 to3 in.) away from the surface of the HomeLink.Keep the indicator light on the HomeLink in view whileprogramming.
3. Simultaneously press and hold the hand- held garagetransmitter button along with the selected HomeLink button.
4. When the indicator light on the HomeLink changes from aslow to a rapid flash after 20 seconds, you can release bothbuttons.
5. Test the operation of the HomeLink by pressing the newlyprogrammed button. If programming a garage door opener,check to see if the garage door opens and closes.
If the garage door does not operate, identify if your garagetransmitter is of the “Rolling Code” type. Press and hold theprogrammed HomeLink button. The garage door has therolling code feature if the indicator light (on the HomeLink)flashes rapidly and then remains lit after 2 seconds. If yourgarage transmitter is the “Rolling Code” type, proceed to theheading “Programming a rolling code system".
6. Repeat steps 2 through 5 for each remaining HomeLinkbutton to program another device.

Programming a rolling code systemIf your device is “Rolling Code” equipped, it is necessaryto follow steps 1 through 4 under the heading“Programming the HomeLink” before proceeding withthe steps listed below.
1. Locate the “training” button on the ceiling mounted garagedoor opener motor. The exact location and color of the buttonmay vary by brand of garage door opener. Refer to the owner’sguide supplied by the garage door opener manufacturer for thelocation of this “training” button.
2. Press the “training” button on the ceiling mounted garagedoor opener motor.Following this step, you have 30 seconds in which to initiatestep 3 below.
3. Press and release the vehicle’s programmed HomeLinkbutton twice. The garage door may open. If the door doesopen, the programming process is complete. If the door doesnot open, press and release the button a third time. This thirdpress and release will complete the programming process byopening the garage door.
The ceiling mounted garage door opener motor should nowrecognize the HomeLink unit and be able to activate thegarage door up/down.
4. Repeat steps 1 through 3 for each remaining HomeLinkbutton to program another rolling code system.

Programming an entrance gate /Programming all devices in the Canadianmarket
1. Decide which of the 3 HomeLink buttons you want toprogram.
2. Place your hand-held gate/device transmitter 25 to 75 mm(1 to 3 in.) away from the surface of the HomeLink.Keep the indicator light on the HomeLink in view whileprogramming.
3. Press and hold the selected HomeLink button.
4. Continuously press and release (cycle) the hand- heldgate/device transmitter button every two seconds until step 5is complete.
5. When the indicator light on the HomeLink changes from aslow to a rapid flash after 20 seconds, you can release bothbuttons.
6. Test the operation of the HomeLink by pressing the newlyprogrammed button. Check to see if the gate/device operatescorrectly.
7. Repeat steps 1 through 6 for each remaining HomeLinkbutton to program another device.

Programming other devicesTo program other devices such as home security systems,home door locks or lighting, contact your authorized Lexusdealer for assistance.

Reprogramming a buttonIndividual HomeLinkbuttons cannot be erased, however, toreprogram a single button, follow the procedure “Programmingthe HomeLink”.

(b) Operating the HomeLinkTo operate the HomeLink, press the appropriate HomeLinkbutton to activate the programmed device. The HomeLinkindicator light should come on. The HomeLink continues tosend the signal for up to 20 seconds as long as the button ispressed.

(c) Erasing the entire HomeLink memory(all three programs)To erase all previously programmed codes at one time, pressand hold down the 2 outside buttons for 20 seconds until theindicator light flashes.If you sell your vehicle, be sure to erase the programs storedin the HomeLinkmemory.

CAUTION
When programming the HomeLink UniversalTransceiver, you may be operating a garage door orother device. Make sure people and objects are outof the way of the garage door or other device toprevent potential harm or damage.
Do not use this HomeLink Universal Transceiverwith any garage door opener that lacks the safetystop and reverse feature as required by federal safetystandards. (This includes any garage door openermodel manufactured before April 1, 1982.) A garagedoor opener which cannot detect an object(signaling the door to stop and reverse), does notmeet current federal safety standards. Using agarage door opener without these features increasesrisk of serious injury or death.
This device complies with Part 15 of the FCC Rulesand with RSS-210 of the Industry Canada. Operationis subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2)this device must accept any interference received,including interference that may cause undesiredoperation.
WARNING: This transmitter has been tested andcomplies with FCC and Industry CanadaDOC/MPAC rules. Changes or modifications notexpressly approved by the party responsible forcompliance could void the user’s authority tooperate the device.

Coco24 · 16-05-2019 22:11:31

J'ai trouvé la doc en anglais avec la même procédure probablement issue du même fichier.
Procédure valable pour un transmetteur à émission simple ou transmetteur à code tournant.

smu · 17-05-2019 07:25:56

Il y a un manuel multilingue comprenant le français, mais est-il adapté à ton système ?
https://www.lexus-tech.eu/aimuploads/%7 … 0080-0.pdf

Alain0044 · 11-10-2019 17:38:49

Des nouvelles sur le sujet ?
Quelqu'un a pu le faire installer après ?
J'aimerais bien avoir ça dans mon RX pour ouvrir ma porte de garage

smu · 12-10-2019 08:21:05

Les notices d'installation pour le RX Gen3 mentionnent clairement "without moonroof" ... désolé sad
Il te reste l'OEM, certains sont assez discrets et facile à installer.

Annonce

#1 06-04-2019 18:24:00

Compatibilité Homelink LS 430

#2 06-04-2019 21:08:27

Re : Compatibilité Homelink LS 430

#3 08-04-2019 19:49:36

Re : Compatibilité Homelink LS 430

#4 08-04-2019 20:07:26

Re : Compatibilité Homelink LS 430

#5 16-05-2019 13:01:09

Re : Compatibilité Homelink LS 430

#6 16-05-2019 20:57:20

Re : Compatibilité Homelink LS 430

#7 16-05-2019 22:11:31

Re : Compatibilité Homelink LS 430

#8 17-05-2019 07:25:56

Re : Compatibilité Homelink LS 430

#9 11-10-2019 17:38:49

Re : Compatibilité Homelink LS 430

#10 12-10-2019 08:21:05

Re : Compatibilité Homelink LS 430

Pied de page des forums